Skip to content

Spectrum Full Aperture Glass Solar Filter for 283 mm - 289 mm OD Telescopes - ST1150G

To ensure that the solar filter you buy will fit properly, please take a few moments and measure the outside diameter of your telescope, spotting scope or binoculars before you order. Remember, the solar filter needs to fit snugly around the front of the tube assembly that holds the optics. If the filter is slightly larger than its diameter, the filter can be made to fit by the addition of self-stick felt spacers to the inside of the cell. However, if the filter is too small it will not fit, and that would be a shame. So please, measure before you order. Thanks.

Spectrum Full Aperture Glass Solar Filter for 283 - 289 mm OD Scopes

This Spectrum Full Aperture Glass Solar Filter fits the following instruments:

  • Celestron 10" Newtonian
  • Orion 10" SkyWatcher

The ST1150G Full Aperture Glass Solar Filter with 293 mm inside diameter provides a safe way to directly view the sun. It allows the maximum amount of light possible to pass through to your telescope, using the entire aperture of your optical tube to enable the finest daylight viewing quality with limited atmospheric instability. When instability does occur, a mask can be placed over the filter for sufficient aperture reduction.

When directly viewed using this durable premium solar filter, the sun will appear in an organic yellowish-orange state. This filter contains felt padding and a centered aluminum cell that attach to the end of the telescope with nylon thumb screws. The ST1150G Solar Filter is made with hand-selected glass of superb quality with reflective coatings that are meticulously inspected.

This filter comes in foam-lined box with plastic wrapping to avoid any possible impairments while shipping. The box also provides a convenient method for storing the filter between uses. Full instructions on how to properly use and maintain your filter are included.

Spectrum ST1150G Full Aperture Glass Solar Filter Specifications

  • Inside Diameter: 11.5" (293 mm)
  • Clear Aperture Diameter: 9.5" (241 mm)
  • Fits instruments with an outside diameter range of 11.125" - 11.375" (283 mm - 289 mm)

In order to assure a proper fit, please be sure to measure the outside diameter of your telescope before committing to purchase a specific solar filter as telescope specifications may be modified with subsequent versions due to re-designs, etc.

What About Your Finderscope?

Adding this solar filter to your telescope will adequately filter the light coming through your focuser, but have you considered what you’ll do about your finder scope?

Here are some suggestions for dealing with your finder that will assure you do not damage your eyes (or anyone else’s) by looking at the Sun through your telescope’s unfiltered finder:

  • Remove Your Finder. Ditching your finderscope when solar viewing will remove the possibility of someone accidentally looking through it to spot the Sun. Of course, not having a finder makes centering the Sun in your eyepiece more difficult, but with practice, it can be done. Set the mount down so the telescope is pointing in the direction of the Sun. Put the main solar filter on so you can check your progress, and then move the telescope around until it casts a shadow that produces a nice, sharp silhouette of the scope. The OTA will look circular. Now move your telescope up or down with your hand controller, slow motion controls, or very carefully by hand if required while looking through the eyepiece. You will not get a warning when you are close, but you should be able to align with the Sun using this method. Practice ahead of time before any big event, like an eclipse, to make sure you’ve got the process down.
  • Filter Your Optical Finder. This solution is not recommended for a reflex or red dot finder since it is too easy to accidentally look around the window. If you have one of these finders we recommend you either remove it or replace it with a dedicated solar finder (see below).

    To make your optical finderscope safe for solar viewing you’ll need to buy a piece of Baader Solar Film for Visual Use. This film comes in different size sheets and cuts easily with scissors, allowing you to make your own filter. You can go super low-tech and use a rubber band to hold a piece of the film firmly around the finder or you can get fancy and build your own slip-on solar filter. However you attach the solar film, you need to make sure there are no light leaks at all and that it doesn’t accidentally fall off when you move your telescope around. Any unused film can store flat between two pieces of cardboard and will keep for years. It is nice to have around, just in case of a solar emergency :-)

  • Buy a Dedicated Solar Finder. Check out the Tele Vue Sol-Searcher Solar Finder. This special finder can only be used when observing the Sun, but it works very well. The Sol-Searcher is reasonably priced and can be attached to your telescope with Velcro or with #10-32 screws (user supplied).